Search Results

A new truck type street sweeper has been developed which incorporates some of the sweeping advantages of a three wheeled sweeper (tricycle steer) and the transport advantages of a legal highway truck. It offers major productivity improvements through better operator environment and decrease of nonsweeping time in the operational cycle. It is possible for a small “short line” special purpose vehicle manufacturer to develop, test, and produce such a vehicle and meet Federal regulatory requirements with limited “In house” design and testing facilities. Here this was accomplished through judicious augmentation by outside specialized design and testing organizations.

In today’s Automotive world, there is NO need to advocate “Light weighting”. Government policies for carbon footprint reduction combined with high safety standards are driving OEMs to adopt advanced manufacturing technologies. Steel hot forming is selected as most preferred way to reduce weight as it is easy to adopt and commercially known. It had many advantages compare to conventional cold stamping of standard and high tensile steel. The process consists of heating blank to nearly 1000 °C and quenching it in tool to for martensitic structure. Higher strength up to 2000 MPa can be achieved by this process. There are many examples where part weight is reduced by 15 to 20 % by this method. But Steel hot forming has limitation as specific density of steel is still high. Thus, there is limitation to its weight reduction capability. For further reduction, OEMs have started exploring Aluminium hot forming.

As a part of testing the braking performance of motorcycles, the method designed for evaluating the very changes caused in brake characteristics due to heat fade has been recently receiving the close attention of ISO and ECE. With the cooperation of the members of the Motorcycle Brake Subcommittee of Japan Automobile Manufacturers Association we measured temperature changes in the brakes and braking force distribution in motorcycles being driven downhill, based on which we find simple and highly reliable simulation test methods on a flat test course. As for test method, we found the STOP method of repeated starting and stopping more suitable to motorcycles than the SNUB, method of making non-stop running. For both methods we also found test conditions offering the highest correlation to actual down-hill driving.

Carburetor repeatability at idle was investigated both on the carburetor precision flow stand and on a chassis dynamometer equipped with exhaust emission test equipment. It was determined that some factors which significantly affect idle fuel flow repeatability on the carburetor test stand are: 1 Surface roughness of mating parts in the fuel bowl inlet system. 2 Inlet valve eccentricity. 3 Hydraulic shock in the fuel supply circuit. In addition, vehicle testing had demonstrated that carbon monoxide changes at idle may occur with constant fuel-air ratio due to changes in fuel temperature. Cycle tests have also shown a relationship between fuel temperature and carbon monoxide levels.

In 1961 the Consumers’ Association in Britain set up a car test unit, and in 1962 the first car test reports were published. These later became the ‘Motoring Which?’ quarterly supplement to ‘Which?’ magazine. The methods and general sequence of the CA car testing procedure are first outlined. The Human Factors contribution to this testing programme is then described. The contribution broadly takes two forms. First, human factors reference data and guidance are provided to assist with the planning and interpretation of the objective measurement programme run by the test unit. Second, an extensive Human Factors Questionnaire (HFQ) programme is organised, and the results are reported, quarterly for every group of test cars. The initial planning of the Human Factors contribution is described; then the essential features of the HFQ programme, and its successive stages of development over the years to the current form with computerised analysis and output are reviewed.

This paper describes preliminary findings on an expert system that uses both operator and transducer inputs in ‘almost’ real-time to diagnose scrap type and recommend corrective action to reduce/eliminate further production of this scrap type. During the development of the expert system, equal consideration was given to hardware installation and debugging; system architecture, logic, and triggering; and knowledge acquisition. The system is applied to a specific manufacturing process; however, the ideas are applicable to a wide range of problems in the production environment.

Using renewable fuels is a reliable approach for decarbonization of combustion engines. iso-Butanol and n-butanol are known as longer chain alcohols and have the potential of being used as gasoline substitute or a renewable fraction of gasoline. The combustion behavior of renewable fuels in modern combustion engines and advanced combustion concepts is not well understood yet. Low-temperature combustion (LTC) is a concept that is a basis for some of the low emissions-high efficiency combustion technologies. Fuel ɸ-sensitivity is known as a key factor to be considered for tailoring fuels for these engines. The Lund ɸ-sensitivity method is an empirical test method for evaluation of the ɸ-sensitivity of liquid fuels and evaluate fuel behavior in thermal. iso-Butanol and n-butanol are two alcohols which like other alcohol exhibit nonlinear behavior when blended with (surrogate) gasoline in terms of RON and MON.

This specification covers the characteristics of glass beads used for peening, and provides for standard glass bead size numbers.

This specification covers the characteristics of glass beads used for peening, and provides for standard glass bead size numbers.

THE PURPOSE of this experiment was to determine the role of residual stresses in fatigue strength independent of other factors usually involved when residual stresses are introduced. It consisted of an investigation of the influence of residual stresses introduced by shotpeening on the fatigue strength of steel (Rockwell C hardness 48) in unidirectional bending. Residual stresses were varied by peening under various conditions of applied strain. This process introduced substantially the same amount and kind of surface cold working with residual stresses varying over a wide range of values. It was found that shotpeening of steel of this hardness is beneficial primarily because of the nature of the macro-residual-stresses introduced by the process. There is no gain attributable to “strain-hardening” for this material. An effort was made to explain the results on the basis of three failure criteria: distortion energy, maximum shear stress, and maximum stress.*

To enable the tests required for development work to be performed with maximum efficiency, the Zwick Roell Group (ZwickRoell) – a global supplier of materials testing machines based out of Ulm, Germany – developed a materials testing machine that can be equipped with both a temperature chamber and a high-temperature furnace.

“Zoning” a catalytic converter involves placing higher concentrations of platinum group metals (PGM) in the inlet portion of the substrate. This is done to optimize the cost-to-performance tradeoff by increasing the reaction rate at lower temperatures while minimizing PGM usage. A potentially useful application of catalyst zoning is to improve performance using a constant PGM mass. A study was performed to assess what the optimum ratio of front to rear palladium zone length is to achieve the highest performance in vehicle emission testing. Varying the zone ratio from 1:1 to 1:9 shows a clear hydrocarbon performance optimum at a 1:5.66 (15%/85%) split. This performance optimum shows as both a minimum in FTP75 non-methane organic gas (NMOG) emissions as well as a minimum in hydrocarbon, carbon monoxide, and nitrogen oxide light-off temperature. Overall, an improvement of 18%, or 11 mg/mi of combined NMOG+NOx emissions was obtained without using additional PGM.

In a 2-year program sponsored by SJAC, an aqueous electroplating process using alkaline Zn-Ni with trivalent chromium post treatment is under evaluation for high strength steel for aircraft application as an alternative to cadmium. Commercial Zn-15%Ni rack/barrel plating solutions are basis for plating aircraft parts or fasteners. Brightener was reduced from the original formula to form porous plating that enables bake-out of hydrogen to avoid hydrogen embrittlement condition. Properties of the deposit, such as appearance, adhesion, un-scribed corrosion resistance, and galvanic corrosion resistance in contact with Al alloy, were evaluated. Coefficient of friction was compared with Cd plating by torque-tension measurements. Evaluation of the plating for scribed corrosion resistance, primer adhesion, etc. will continue in FY2007.

For over a decade, industry prognosticators have been predicting that the use of plastics by automakers would soon surpass the deployment of metals in automobiles, While there is no denying that plastics have made inroads, it recently has become apparent that metal will retain its position as the prime car material for the foreseeable future. One reason for the revised forecast is the development of improved zinc coatings for the automotive industry. Such material as electrogalvanized and Galfan™ are shaping up as steel's saviors when it comes to ensuring that metal will continue to play the major role on car assembly lines. Meanwhile on the other side of the equation, developments in zinc die casting technology have taken the edge off plastics' forward thrust into both functional and decorative car part applications.

Copper and brass radiators have served the automobile industry for many years using traditional fabrication processes. Demand for newer and stronger radiators with lighter weight for the modern vehicles prompted investigation of alternate materials. Properties of zinc alloys and their compatibility with brass suggested these could be used for radiator manufacture. Many zinc alloy compositions were investigated in the initial studies, because a solder alloy has to have many positive attributes. The first screening studies evaluated the ability of the solder to spread over copper and brass surfaces, representing tube, fin, and header materials. The second most important feature was the melting range of the developed alloy. In order to retain the anneal resistance of the fin and temper in the tube it was desirable to have a zinc solder with a melting temperature at 800°F or less.

This specification covers the requirements for producing a zinc phosphate coating on ferrous alloys and the properties of the coating.

This specification covers the requirements for producing a zinc phosphate coating on ferrous alloys and the properties of the coating.